![]() This manifold should flow to the constructor in the 13th column and also flow forwards.įor this next part we will be placing the assemblers for the stators and then the motors. ![]() The second manifold will be placed in-front of the three constructors running steel pipes. One in-front of the first six constructors with the mergers all flowing towards the third constructors’ merger (This should be facing forward) You will also need to connect the 8th and 10th constructor to the two remaining splitter outputs.Īt this point build two merging manifolds in-front of the constructors. Note these constructors will all be running at 100% clock-speed with the exception of one constructor which will be set at 33% clock-speed.Ĭonnect the six constructors with elevators, as well as the 9th constructor. Your second line of constructors will be six long, producing wire and in-front of the splitters along the manifold line you just placed. These will produce steel pipes at 100% clockspeed. You should now have three constructors in-front of the steel foundries. At this point we will delete the 7th constructor. For this stage, we will place 10 constructors in a row two steps in-front of the first splitter and running all the way to the end of the 13th column. We need to place a total of 9 constructors. Start by placing a splitter directly after the last merger, the splitter should be bridging the gap of two foundations, repeat this on each of the following foundations heading to the right. We shall now place six splitters along this row. Place elevators after the smelters and then run the conveyor line to the mergers, do this for all three smelters. ![]() From here place a splitter in-front of the merger (done by stacking three stackers, and deleting the bottom two.) Make sure the merger and splitter are connected by a conveyor.Īlong the same row as the splitter you will want to place mergers in a row facing towards the right of the grid, place these mergers in-front of the smelters. Once done connect the elevator from the foundry output to the top merger, then delete the two mergers beneath. The merger should be two steps in-front of the chosen output and stacked three mergers high. Note for a perfect merger connection, place the merger first. In-front of the foundry outputs place down elevators, this will feed into a merger. Note we shall use overhead merging and splitting manifolds in this guide. Iron ore and coal for the steel foundries. Next you will need to build a manifold for the three inputs. I recommend that you keep the smelter outputs in line with the foundry outputs, although this is not necessary. Next place the three smelters in the centre of the first, second and third columns foundations. You can now delete the constructor, should you wish. From here place the second foundry flush against the first one on the left-hand side. Directly in-front of this place a foundry bridging the two foundations in-front of it. To begin, place down a constructor against the edge of the thirteenth (last) foundation. Stator & Motor Super-Efficient Build Guide In order to construct this layout we will require: The aim of this layout is to reach 20 stators per minute, going on to create 10 motors per minute. for Turbo Motors I can decide on one of the recipes and then make a new tab for each of the 4 items I would need and then make that in a separate factory and get it all together in the end.Stator & Motor Super-Efficient Factory Layout And for very complex things I can make 4 different tabs. When I have something that I like, set the amount to something I likeįor more complex things I can spend a lot of time.removes screws or see the differences what some things will do. Play around with different things, e.g.Remove recipes I do not want, I do not differenciate between alt and normal ones.Remove things I do not want to use (e.g.Select the thing (or things) I want to make.I also often compare different recipes and I only use the maximum to see what number I could get and then change the numbers so the amount of machines I want are nice. What I do when I am ready is take a screenshot (You can re-arrange the layout by dragging) as well as the link (use the share button) and then save those, so I can reply on those. ![]() You will have to learn to use it to make most use of it. The thing I like about that website is that it isn't a 1 click solution. I’m at a point where my factories are getting too complex for my brain to handle on its own. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |